I'm looking to do some welding jobs for my fellow GotMud? members..
I can do driveshafts, weld up rollcages (if you bend them up), suspensions, bumpers, hitch mounts, and a ton more. If you dont know if it could be done ASK me!
Due to the recent actions of Bogginboy, i will be requiring a 50% deposit before i build your item (This is to protect the investment i make to build it) Your check will NOT be cashed until your item has been completed and you are satisfied with the workDriveshaft shortening: $50
Driveshaft Lengthening: You supply new shaft center and yokes $50. I supply shaft, you supply yokes $100
Bumpers starting at $75-150 (depending on steel type, and design), will do a package deal for front and rear bumpers. Add 2 Drings (15,000lb) for $50, 2" reese hitch reciever for $50
Hydraulic steering: will set up for $200 if you supply power steering pump, steering valve, steering collum, and hydraulic ram
Will install at
no charge if you bring the vehicle to me.
I can currently build parts, ready to install for the following vehicles:
Chevy/GMC
Gen 1 S-Series trucks 83-94
Gen 2 S series trucks 95-04
Full Size 89(era trucks) not sure off the top of my head
CJ-7s
XJ's 88 and 2000 available to me
Anything else just ask!
If you break ANY of my parts due to lack of workmanship i will replace them for FREE
Few of the parts i offer done within a week...
CJ-7 Front and Rear bumpers
98+ S10/S15 front bumper Starting at $75
(http://i7.photobucket.com/albums/y284/shmotz405/Fab%20work/bumpers/P1010055.jpg)
95-97 S10/S15 front bumper Starting at $100 (will get up-to-date pictures later, this was in mid progress)
(http://i26.photobucket.com/albums/c148/cannaert/Sonoma/MonsterJAm030.jpg) (http://i26.photobucket.com/albums/c148/cannaert/Sonoma/MonsterJAm030.jpg)
Hitch Install
$50 you supply the hitch
(http://i7.photobucket.com/albums/y284/shmotz405/Fab%20work/100_2202.jpg)
(http://i7.photobucket.com/albums/y284/shmotz405/Fab%20work/bumpers/100_0001.jpg) (http://i7.photobucket.com/albums/y284/shmotz405/Fab%20work/bumpers/100_0001.jpg)
how much to make a rear bumper for a 92 xj with one or two tow points pm me cause ill forget about this lol
I need some very light cutting and welding done for a hi-lift jack mount bracket for my roof rails. I already have the materials and measurements taken/drawn on the metal. Give me a call I can stop by sometime. -brodie 248 877 8932.
could u supply the parts for Hydraulic steering and if yes how much for everything
Quote from: Trent on December 05, 2008, 03:25:40 PM
does the $50 include the drings and putting them on
yes
Quote from: Trent on December 05, 2008, 03:25:40 PM
would you be able to weld them on a round bumper
yes
Quote from: MOOSE13 on December 05, 2008, 03:37:32 PM
could u supply the parts for Hydraulic steering and if yes how much for everything
i COULD but, i dont like to do it out of my pocket... i've had people make me build something for them only to not show up for it......
i dont really know what to get as far as parts so what is a ballpark figure for the cost for all the parts
how much for a front and rear bumper combo for a 93 xj with d rings and pics or drawing of what it would look like thanks and how would u fasten them thanks