HELP... wheels will not come off

[chevyjake]

Pull the lugs off shoot some PB blaster on the studs to soak the back side of the wheel, let it sit and either smack it with a sledge hammer or drive it around in circles/ back and forth. just be careful not to take the wheel to the shin when your hitting it with the sledge.


Good Luck..

[OHEARN.2012]

try jumping it like the dukes of hazzards did??

[old school truck dude]

The lugs aint holdin it, the center is. Soak the center real good, use a wood block and sledge on the back side of the rim or a porta power. You can also use a bottle jack or a high lift jack or whatever ya got (I use a scew jack for just about everything) and wood block if you can find a spot to push from or possibly chain it to the axle housing some how. Get some pressure on it as far out to the outside edge as possible then smack it. It WILL come off. Clean it all up real good once its off and put some GREASE not oil on the center so this dont happen again.

[4x4xdodgeman]

I got!!!!    get realy pissed off and do everything every body said!!!

[OHEARN.2012]

I got!!!!    get realy pissed off and do everything every body said!!!

try jumping it first

[woody11769]

Good luck it sucks when it happens like everyone said you need a bigger hammer it'll come

[rangerwheelinmike]

take the lugs off put a chain around the rim and hook it to another truck put in in 4low and stand on it??

[four_by_ken]

Did it ever come off?

[WHITE KNIGHT]

p b blaster will work if you give it time like over night

[ToughBowtieTruck]

Did it ever come off?

I know, this suspense is killing me !!!

[spr_chicken]

Did it ever come off?

I know, this suspense is killing me !!!

No not yet...

[spr_chicken]

take the lugs off put a chain around the rim and hook it to another truck put in in 4low and stand on it??

I'm considering this...

[spr_chicken]

I tried using a come along attached to a tree and hiting the wheel with a sledge hammer. I put a jack stand under one side and I pulled the truck off of it once. I'm affraid i'm going to break the c-clips or the axle shafts.

I am going to try again. I am going to do the same thing, but this time I am going to let the air out of the tire so I can hit the rim better. If that doesn't work I am going to pull the axle apart and try to pressing the wheel studs out.

[RIP_K52007]

you could do the opposite, max the tire pressure out so the tire is not so bouncy vs the hammer lol if they are load range D you could probably put 65psi in them

put the lug nuts half way and go beat the out of it til it falls off

[Hammerlane]

add some heat.. propane torch type..
heat up around the center n' lugs..

[rangerwheelinmike]

I tried using a come along attached to a tree and hiting the wheel with a sledge hammer. I put a jack stand under one side and I pulled the truck off of it once. I'm affraid i'm going to break the c-clips or the axle shafts.

I am going to try again. I am going to do the same thing, but this time I am going to let the air out of the tire so I can hit the rim better. If that doesn't work I am going to pull the axle apart and try to pressing the wheel studs out.

wow I guess I would take the lug nuts half way off and go beat on it

[Bigolcummins]

so its locked itself up in the center hub pretty much?

[J.C.]

Hell by now i woulda taken out the c clips

[Crazymays77]

once you get it off clean the center of the rims so there is more clearance there. that way it doesnt happen again.

[Newbie]

p b blaster will work if you give it time like over night

pb is the way to go with a torch!