Mud Force One

MUD HUNTER · July 04, 2010, 04:10:19 AM

We got the beast pulled out of the shop today, and put the big dawg tires on. This thing is simply massive...

BIG DOG · July 05, 2010, 01:11:17 PM

sweet

rob69 · July 19, 2010, 12:13:25 AM

BAD ASS!!!

MudForceOne · July 23, 2010, 01:30:02 AM

New master cylinder & orbital valve to put on in the morning, then test run before it goes back in the barn to get cleaned up. Gonna wrap the bottom, enclose motor compartment, & such. Engine has been fired, runs good, the 240hp injectors worked out. Changed the bus computer out for a pick up computer which added another 900 rpm. Drive shafts have been moched up for test run,but are going to have to be replaced. Front brake rotor is in, but need to still work on the front caliper. Have yet tested the air togle switch to the transfer case. Do have on board compressor in working order. Stacks have been completed out through the deck lid (trunk still in working order) . Overall Dimensions are 30'+ long, 10'5" tall, & 12'6" wide on the monster truck tires.

scottsdale · July 23, 2010, 08:16:18 AM

that rocks thats thing is going to be a hit com prom time

ProGrade · July 23, 2010, 11:10:51 AM

that thing just rocks.

bigmud44 · July 24, 2010, 11:50:36 AM

Quote from: professional grade on July 23, 2010, 11:10:51 AM
that thing just rocks.

x2

bigtruckpwr · July 24, 2010, 09:56:02 PM

great for a wedding!

STEUERDUKES · July 24, 2010, 11:18:37 PM

redneck taylor · July 24, 2010, 11:59:46 PM

dam thats cool the front is goin to be out of the mud hole before the back tires get in it sweet build

Jjay78 · July 25, 2010, 05:12:24 AM

that thing is huge,

MudForceOne · July 25, 2010, 11:56:43 AM

Quote from: redneck taylor on July 24, 2010, 11:59:46 PM
dam thats cool the front is goin to be out of the mud hole before the back tires get in it sweet build

Thank You !

MudForceOne · July 25, 2010, 11:58:57 AM

Still awaiting the return of the orbital valve so I can get the test run on it before back into the garage for completion. I did pick up the Name decals for the sides of it, they are 12"x 12' I will try to get a pic up here once they go on.

MudForceOne · August 02, 2010, 01:24:19 AM

Headed to Blue Water Labs in the morning to have the power steering pump internal by-pass altered & pick up the variable control external by-pass. Going to have them out to install a hydro pressure guage in the dash to watch & see where the by-pass needs to be set. Also picking up a hydro brake booster from Hallus performance to swap over as there is no vacuum avialible on this thing.

MudForceOne · August 09, 2010, 12:53:26 PM

well we added an external steering by-pass(removed the by-pass in the steering pump), added an electric vacuum pump( for braking), de-wired the dash, corrected the fuel pedal, rewired the ignition key & mounted it in the dash.

bigxploder · August 09, 2010, 05:42:29 PM

TITTIES x2

MudForceOne · August 16, 2010, 11:40:32 AM

B&M Super cooler just added to the power steering. Another test run soon !

rob69 · August 17, 2010, 04:45:12 PM

Make sure you get some vids!!

MudForceOne · August 30, 2010, 01:01:58 AM

Second test run was done last Sunday to find the design of the rear axle mounting needed some serious work, a little re-engineering. Almost ripped it out from under the truck, got the new parts on order to fix this. Then we can add the programmer (additional 100hp).

MudForceOne · September 07, 2010, 03:08:11 AM

Programmer coming tomorrow ! The rear suspension issue has been solved (for now anyhow). Removed the panard bar & added half of a four link system to the rear. We made it through the Peach Festival Parade today, next will be the "Sticks", see how it likes a beating in the mud.