boggers

[84silverado]

ok so i was wondering today in school if i get these boggers ive been saving up for. would it be better to cut all 4 or just the back 2? they are 33's and will be on a 10 bolt axle, if this means anything to ya. just wondering what you guys would do cause i was thinking just the back 2 but suggestions are great

[Blazin40s]

Back 2

[84silverado]

im just gunna beat the living piss outta the tires like i do my truck. so wear really isnt an issue but ive never heard of them wearing out faster, i always figured theyd wear less

[betterbeaters]

dont cut them unless you got alot of power!

[84silverado]

how many ponies you think for cut boggers?

[betterbeaters]

that size with enough gear(3.73 +) a good mild 350 would work fine.... 

[84silverado]

i have 3.73's and a 305 with alil work, .40 over edelbrock performer rpm intake and 600 carb and a good size cam

[betterbeaters]

it should work..  33s are little tires I know 44 cut boggers will rob a ton of power! 

[84silverado]

a 44 is alot of tire though! lol

[betterbeaters]

44s are just right!  wish I had them on both trucks!

[BIG DOG]

save more money and go bigger  a full size truck on 33s   just sounds like a stuck fest  not to knock ya  i'm just happy your playing and havin fun.   dont cut them  your not racing  and your opening more tire surface up to more damage  

[Squirell]

save more money and go bigger  a full size truck on 33s   just sounds like a stuck fest  not to knock ya  i'm just happy your playing and havin fun.   dont cut them  your not racing  and your opening more tire surface up to more damage 

x2

[hot rod heep]

the only reason i would cut  a bogger was if it was wore out and almost smooth then cut  it and get the full life u can out of it   and cut boggers bite so hard  u will be braking parts  with them   just my 2 cence

[BAD APPLE]

Don't cut them until the front lug edge is wore down then cut em but don't take too much out just the small lug and the front edge of the lug to to make it sharp again, if u just got with it cut up good if u put a whole in one don't worry bout it the make boots ane patches every day

[85cHeavyMetalBogger]

i was gonna cut my 35's but havnt done it yet. i guess im not sure if i want to do it or not....i run 355/400/208 with D60's/410 gear. not sure how it would work out, and u cant put the lugs back on..lol.

[84silverado]

thank you guys for the input. this was the kinda stuff i needed  i dont think imma cut them, and i think ill go bigger too cause of the little bit of encouragment from BIG DOG lol i guess ill have to start with my motor build before i get my rubbers haha i think ill need a few more ponies with 36'' boggers

[390JOE]

the only reason i would cut  a bogger was if it was wore out and almost smooth then cut  it and get the full life u can out of it   and cut boggers bite so hard  u will be braking parts  with them   just my 2 cence

and this guy is talking from experience.

but if you cut anything i would say a ground hawg or something like that.

[85cHeavyMetalBogger]

i think you might need some bigger axles for 36's, maybe. depending on how u wheel.

[84silverado]

i dont think ill do anything enough to break my axles. i believe theyll hold, even if i get smaller 35's. but if do. o'well, thats the name of the game. wheel and fix, then do it all over again lol 

yea i got 2 hawgs to play with but most of the time they just stay in the back of the truck for spares. some times i put them on cause they are alil wider but they usually sit in the backand enjoy the ride haha

[Blazin40s]

my buddy broke a lot of shafts with 35 baja claws which is a much less agressive tire then a bogger, when he was runnin half tons and stock 318