Bud Wogger

[Kyle]

Mine had the same symptoms before i finally lost all idle pressure. Mine was cuz the rear main cap never had the oil pump torqued to it when it was line honed. Once that bearing went so did the rest. Dont take long. I doubt ur crank had anything to do with it

[BAD APPLE]

Mine holds 70 when first stated but one I run it a few times it drops to 30-35 at idle been like that for three years

[just one more]

rule of thumb, 10 lbs per 1000 rpms, but not necisarily 10 lbs at 1000 rpm idle, if you are running 6000 rpms you should see roughly 60-70 psi etc....25-35 psi is ok at idle (warm/hot), my engine cold 65 psi at idle, when it warms up, 25-35, both of the engines that i have ran in the last 6 years had/have the same charictoristics with zero problems,

just sayin 

[Bryank]

well gonna tear it apart over winter to see what's up. gonna pick up a decent 350 for my dually hopefully tonight or tomorow and put the racing small block back in it for now. I gotta go wheeling one more time before the years out! i was having to much fun!

[2Twisted]

Last year at trucks gone wild I had a pressure drop about 20 at idle and it ended up being the oil pick up.

[Bryank]

Last year at trucks gone wild I had a pressure drop about 20 at idle and it ended up being the oil pick up.

hmm. it was clean and i made sure to weld this one on so don't think it's that. im pretty sure that torque converter wiped out the thrust bearing and is letting the crank walk around. but on a good note traded my motorcycle for this rebuilt odly colored 357! it runs great and should work perfect in the dually. bogger is getting the sbc back for now. it should rip this time around!

[Bryank]

ready to go! hope it runs good!

[marshall]

Last year at trucks gone wild I had a pressure drop about 20 at idle and it ended up being the oil pick up.

hmm. it was clean and i made sure to weld this one on so don't think it's that. im pretty sure that torque converter wiped out the thrust bearing and is letting the crank walk around. but on a good note traded my motorcycle for this rebuilt odly colored 357! it runs great and should work perfect in the dually. bogger is getting the sbc back for now. it should rip this time around!

I'm willing to bet that motor was built by Jim Stewart. He painted all the motors he built purple.

[Bryank]

Last year at trucks gone wild I had a pressure drop about 20 at idle and it ended up being the oil pick up.

hmm. it was clean and i made sure to weld this one on so don't think it's that. im pretty sure that torque converter wiped out the thrust bearing and is letting the crank walk around. but on a good note traded my motorcycle for this rebuilt odly colored 357! it runs great and should work perfect in the dually. bogger is getting the sbc back for now. it should rip this time around!

I'm willing to bet that motor was built by Jim Stewart. He painted all the motors he built purple.

lol it was built by Charles Brisco. He is the motor guro of hastings! lol. he had like 20 high performance motors in a 1 stahl garage i couldnt believe it. he claims it was the only paint he had laying around. but hey it does run great and the bogger is a ripper now with the small block back in it. plans for next year is to shed some weight. joining the s10 bogger crowd. throwing this beater on it. might have to change the name to the red rocket lol

[marshall]

That's funny, Jim painted his purple because he said nobody else would. Haha

[Bryank]

Haven't done anything to it except for firing it up every once in a while.if I can sell the BBC I'm gonna buy a twin turbo kit for it. Just waiting for spring she is pretty much ready to go.

[355REDNECK]

Haven't done anything to it except for firing it up every once in a while.if I can sell the BBC I'm gonna buy a twin turbo kit for it. Just waiting for spring she is pretty much ready to go.

wanna buy me one for mine to lol

[Bryank]

I just wanna go bogging! Freshening up the Dana 60 and serpentine setup is on the list. Truck is gonna be ready this spring for that oh so great mud!!!!!!!

[cjbogger]

X2 on that

[Bryank]

Axle rebuilt and uprights added.

[cjbogger]

looking good bryan youll like those uprights which size did you put on?

[Bryank]

Thanks they are 1-3/4 to 3-1/2.added these today

[cjbogger]

Thats what i put on the jeep they sound great nice deep tone
did you add those screens on top havent saw them like that before i like. might have to do that myself

[Bryank]

Yeah I just grabbed some stainless screen from work and cut and tacked em in. Got extra at the house if ya want some

[cjbogger]

 ill take ya up on that looks way better than tractor flaps

thanks