BLOOD THIRSTY

[fordrunner]

Looking good keeping up

[Merc09]

I painted the headers and bolted em on. Got some starter bolts and put the starter on. I revamped the dash and made a switch box and a dash thats is a little closer for the guages. I mounted all the guages and started wiring everything up. The fuel cell is finaly secure. And i also started switching my rims around. Getting close!!! I should have it turning over in the next couple days. And running hopefully in a week or 2

[Jthomas]

What else do you need to make her run?

[fordrunner]

If I was that close u wouldn't be able to do pull me out of the shop! Hell the bronco don't have headers, valve covers, proper fuel system and i had to here it run makes me work harder knowing it will rum and that close to the finish but that's me

[Merc09]

I still need an alt. But i have to pull my intake off and put on lifter valley gaskets. Then i can put my dist. in and wire that up. I have to get a tac. I have to hook up the guages. Finish the wiring. Get a upper rad hose. Get oil,trans fluid, gas, and water. Hook up powersteering. And get a rear driveshaft made. Btw on my intake theres a plug right infront of the thermostat housing where i should beable to put my coolant temp switch but its corroded in to the intake. How should i get it out. It allready rounded out the 3/8 drive square in side of it. So idk what to do. Do they make a fitting i could put inline with my rad hose that the cts would screw into? I still have to yun trans lines spark plug wires. Hook up the carb. I also still need fenders and hood hinges. Theres still quite a bit to do but its all the little details lol. Oh and fordrunner i didnt leave my garage for a while. I was awake at 9:30am on tuesday and i didnt go to sleep till 2pm wednesday. Lol

[Jthomas]

I still need an alt. But i have to pull my intake off and put on lifter valley gaskets. Then i can put my dist. in and wire that up. I have to get a tac. I have to hook up the guages. Finish the wiring. Get a upper rad hose. Get oil,trans fluid, gas, and water. Hook up powersteering. And get a rear driveshaft made. Btw on my intake theres a plug right infront of the thermostat housing where i should beable to put my coolant temp switch but its corroded in to the intake. How should i get it out. It allready rounded out the 3/8 drive square in side of it. So idk what to do. Do they make a fitting i could put inline with my rad hose that the cts would screw into? I still have to yun trans lines spark plug wires. Hook up the carb. I also still need fenders and hood hinges. Theres still quite a bit to do but its all the little details lol. Oh and fordrunner i didnt leave my garage for a while. I was awake at 9:30am on tuesday and i didnt go to sleep till 2pm wednesday. Lol

Text me.

[Merc09]

I texted ya. Lol

[Merc09]

ITS REALLY CLOSE TO RUNNING. I NEED A FLOOR SHIFTER, DIPSTICK TUBE AND DIPSTICK FOR THE TRANS, INLINE FUEL REGULATOR, FLUIDS, FINISH WIRING, A REAR D SHAFT MADE AND A SERPENTINE BELT AND SHES READY!

[84silverado]

Just put a rod threw the floor to shift works for me

[Jthomas]

I might have a tranny dipstick tube and dipstick.

It's for a 700r4. Not sure on the difference between the 350 tho

[mud gremlin]

U don't need a regulator its a 7 psi

[Merc09]

Yeah i know i posted that before you texted me lol.

[Merc09]

Well i havent worked on it for a few days, but its back in my garage and im gunna start work on it again. I need to prime the oil pump "Im not sure how so if someone could help that would be very much appreciated.". I got torque converter bolts for it. And im headed to advantage driveline later this week to get my rear driveshaft made and my front driveshaft finished up. I got an upper rad hose and my tac is now mounted. Due date is sept 13 but itll be close but i still have 1 more bog after that thats near me this year and thats oct 20th. I really dont want to cut into my hunting time but what happens happens lol

[Jthomas]

Priming the oil system is easy. Get the tool, or an old pump shaft, and put it in a drill and spin the pump for a few mins. But make sure you got enough oil in the pan, or else it just sucks air.  Should make 60+psi oil depending on the oil pump. Mines a high volume.

[Merc09]

Well i know i have 5+ quarts in a stock oil pan which holds about 6 so i think im good there. Would autozone rent them you think?

[betterbeaters]

what stock pan did you find that holds 6 qts??? all I have found were 5 qt pans i keeping buying aftermarket 7qt pans now lol

[Merc09]

what stock pan did you find that holds 6 qts??? all I have found were 5 qt pans i keeping buying aftermarket 7qt pans now lol

Its a 94 pan off a tbi 350 lol

[Merc09]

Thinking of names for this thing. I had the idea of "DIRTY INTENTIONS" but im not to sure. Maybe you guys could help.

[betterbeaters]

all the tbi motors I had were 5 qt pans lucky you for finding a 6qt

[Merc09]

all the tbi motors I had were 5 qt pans lucky you for finding a 6qt

My 97 vortec is a 6 quart pan too. Lol